Quick Answer
INA826AIDR is a precision instrumentation amplifier for amplifying small differential signals in measurement circuits. Texas Instruments specifies single-supply operation from 3 V to 36 V, with gain set by an external resistor. It can be investigated for bridge sensors and instrument front ends, including medical equipment development. The correct sourcing request names the complete AIDR orderable and the already approved measurement design.
The useful buying question is not whether the amplifier has a broad medical application label. It is whether the released circuit meets its signal, accuracy and system requirements using this exact part. In medical equipment, the component's use still requires board and device qualification for the intended application. An instrumentation amplifier by itself provides neither patient isolation nor approval of a complete medical device, and the RFQ should not imply either.
Key Specifications
TI lists an eight-pin D SOIC for INA826AIDR. The data sheet describes a gain range from 1 to 1000, a maximum offset of 150 microvolts and a typical supply current of 200 microamps. Read the conditions attached to each specification, especially where performance changes with gain or supply voltage.
A rail-to-rail output description does not make every combination of input signal, gain and supply valid. Ask engineering to check the full operating envelope rather than testing a single centre-of-range signal. For incoming material, the relevant procurement evidence is the correct orderable, package, grade and traceable lot record. Circuit performance must then be evaluated in the context in which the amplifier will actually operate.
- Preserve the external gain resistor value, tolerance and temperature coefficient in the measurement error budget.
- Review the permitted input common-mode range together with the required output swing at the chosen gain.
- Identify the source driving the reference pin and verify its effect on measurement offset and common-mode rejection.
Where to Use This Part
Potential uses include pressure or force bridges, process measurement and low-level differential acquisition. TI's data sheet also lists ECG and surgical equipment among application areas. These are starting points for engineering evaluation, not declarations that an arbitrary assembled circuit is suitable for clinical use.
Build a test plan around credible worst cases. A large sensor offset can consume output headroom before the desired signal is amplified. An imbalance in input filtering can affect rejection of interference. A high-impedance reference connection can introduce an avoidable error. These are reasons to preserve the design evidence with the sourcing request; they are not evidence that a new lot has passed a qualification test that has not been performed.
- In a bridge sensor, establish the sensor excitation, expected offset, full-scale differential signal and temperature variation.
- In an instrument front end, examine input protection, bias-current paths and interference pickup from the actual sensor connection.
- In a medical design, assign responsibility for patient protection, fault assessment and the complete verification programme before freezing the BOM.
Pricing and Lead Time
Send the exact part number, required units, destination and assembly need date when requesting an INA826AIDR quotation. State the carrier and document requirements and identify whether alternatives are allowed for review. If the organisation needs continuity for a regulated or validated product, include the approved change-control route without sharing confidential design information unnecessarily.
The checked manufacturer ordering page distinguishes reel and tube orderables. Do not infer that every packaging variant has the same current lifecycle status; reconfirm the exact requested code when placing an order. A related part remaining available does not establish the status or condition of a particular lot offered by an independent supplier.
Obtain dated price and delivery terms. Compare offers using the same quantity, packaging basis and required records. Add internal inspection and release time to planning. If a purchasing option would require new calibration limits or verification work, make that cost and schedule visible to the decision owner instead of hiding it behind a lower component price.
Common Alternatives
Alternatives should be compared as measurement elements. Another instrumentation amplifier may require a different gain equation, input range, reference drive or compensation arrangement. Package compatibility is only one part of that comparison, and visual similarity of an eight-pin outline does not establish equivalent pin functions.
Start with the intended signal and an error budget. Evaluate input offset and drift, bias currents with the actual source impedance, noise over the relevant bandwidth and common-mode rejection at the interference frequencies of interest. Then consider settling, output loading and power behaviour. A device with an attractive single specification can still underperform in the application's most important operating corner.
For an existing medical instrument, route any part change through the organisation's established design-control and risk-review process. For a new industrial sensor, a broader architecture review may be practical while the design is still flexible. In either case, keep the approved part and any proposed substitute on separate RFQ lines. Release the alternative only when the documented evaluation has answered the questions created by its differences.
FAQ
Is INA826AIDR a medical-grade component?
This guide makes no such designation. TI lists medical application areas, but suitability depends on the complete device design and qualification. The amplifier does not itself establish patient isolation, clinical performance or certification of an assembled instrument.
Why can a bridge signal clip despite a small differential input?
Gain, bridge offset, common-mode voltage, reference level and output headroom must be considered together. A small desired signal does not guarantee that all internal and output stages stay within their valid operating ranges.
What distinguishes an exact-part RFQ from an alternate request?
An exact-part RFQ asks for INA826AIDR and its approved documentation. An alternate request additionally supplies the relevant circuit requirements and asks for differences to be declared. A commercial response should keep these two decisions visibly separate.
Request an RFQ review for INA826AIDR
Sources
- Texas Instruments INA826 product information (checked 2026-10-02)
- Texas Instruments INA826 data sheet and orderable addendum (checked 2026-10-02)