SENICO Electronics

Component sourcing and inventory guides

ISO1410DWR: Complete Sourcing Guide & Price 2026

Source ISO1410DWR for isolated industrial RS-485: check half-duplex timing, separate power domains, bus protection, package evidence and RFQ assumptions.

Quick Answer

ISO1410DWR is a Texas Instruments isolated, half-duplex RS-485 and RS-422 transceiver for links operating at up to 500 kbps. It is a practical part to investigate for industrial controllers that communicate across different ground domains. The purchasing decision should start with the required bus speed, approved board footprint and isolation design. Include the complete DWR ordering suffix in the request so a quotation addresses the intended wide-body package and carrier.

A common sourcing mistake is treating every isolated RS-485 device as a single category. A faster family member can have different switching behaviour, while a nonisolated transceiver changes the protection architecture. Before comparing offers, write down what the existing design actually uses: supply on each side, connector arrangement, termination position and control of the driver enable signal. That description helps engineering distinguish a commercial option from a board change.

Key Specifications

The manufacturer identifies this device as a 500-kbps half-duplex transceiver in a 16-pin DW SOIC package. Its logic side and bus side have separate supply requirements. Isolation transfers information between these domains; the device does not include an isolated power source. Procurement therefore needs to keep the transceiver and the approved isolated supply as separate BOM requirements.

Record limits with their test conditions. A withstand test voltage is different from a continuous operating voltage, and a component protection specification is different from proof that an assembled cabinet passes an immunity test. Keep the applicable safety documentation with the exact ordering information rather than copying the largest isolation number from a comparison table.

  • Check VCC1 against the specified 1.71-V to 5.5-V range and VCC2 against the 3-V to 5.5-V range.
  • Verify the 500-kbps maximum data rate against every configured baud rate and the planned protocol overhead.
  • Match the DW package drawing, pin assignment and isolation clearances to the controlled PCB documentation.

Where to Use This Part

This part can be evaluated for PLC communications, building controls and remote instrumentation where a shared differential bus connects equipment with separate local grounds. Half-duplex operation means the same bus pair carries traffic in both directions at different times. Firmware and hardware must agree about when a node drives the cable and when it listens.

Build a representative network before accepting a changed sourcing option. Include the longest expected cable, the actual connector, typical node loading and realistic electrical disturbances. Log communication errors during power transitions rather than checking only a clean laboratory waveform. These are suggested qualification steps; they do not imply that any offered component lot or completed system has already passed them.

  • On a multidrop control network, review addressing, turnaround delay and whether two transmitters can accidentally contend.
  • On a remote sensor link, evaluate the complete cable, termination and ground arrangement under expected installation conditions.
  • On serviceable industrial equipment, test power cycling and cable reconnection while neighbouring nodes continue operating.

Pricing and Lead Time

An actionable RFQ states ISO1410DWR, required quantity, shipment destination, assembly date and whether the line can accept partial quantities. Add the desired carrier format and any document requirements. Request a written response separating the quoted quantity from a supplier's broader sourcing estimate, because those figures answer different planning questions.

The article does not establish a market price or committed delivery date. Those depend on a dated offer and the specific lot proposed. Ask whether a quoted schedule describes order processing, supplier dispatch or arrival at the destination. For a production plan, also identify the internal time needed for receiving inspection, document review and release to assembly.

Compare offers on an equivalent basis. A reel suitable for automated placement may avoid handling work that a collection of short tape strips would create. Conversely, a prototype build may not need a full production carrier. Note the practical difference in the comparison sheet without assuming that either format is unacceptable. Resolve permitted date codes and lot splitting before purchase approval.

Common Alternatives

For alternatives, first decide whether the requirement is to preserve a released board or redesign an interface. Those tasks have different acceptance criteria. An isolated transceiver with another speed grade, duplex arrangement or default behaviour deserves a new comparison even when its family name looks familiar.

Create a matrix covering pin function, direction control, logic thresholds, bus loading, propagation delay, supply sequencing and package dimensions. Include the isolation working conditions relevant to the end product. A matched headline data rate leaves many of these questions unanswered. Record the engineering reviewer and the evidence used for each accepted difference.

Where noise rather than throughput limits a network, changing to a faster device is not automatically useful. Cable topology, stubs and termination may dominate the problem. Obtain measurements before substituting the transceiver. For maintenance purchases, retain the exact approved part request as its own quotation line and place any proposed alternate on a separate line requiring approval. This preserves a clear decision trail from the RFQ through receiving and assembly.

FAQ

Does ISO1410DWR supply isolated power?

No. TI lists no integrated isolated power for ISO1410. Plan and qualify the power arrangement on each side separately. A signal isolation barrier does not itself provide the bus-side energy required by the transceiver.

Can a faster RS-485 part be accepted automatically?

No. Review the full electrical and mechanical comparison, then test the intended network. Faster signalling capability does not establish matching duplex operation, timing, protection behaviour or suitability for the existing cable topology.

What should a buyer send with an urgent RFQ?

Send the complete part number, quantity, destination, assembly need date, approved carrier and required traceability documents. Mark alternates as subject to engineering review, and ask the supplier to identify the actual basis and validity of its delivery proposal.

Request an RFQ review for ISO1410DWR

Sources