SENICO Electronics

Component sourcing and inventory guides

ISO1452DWR: Complete Sourcing Guide & Price 2026

Review ISO1452DWR for fast industrial full-duplex links, including separate transmit and receive pairs, timing budget, exact package and sourcing evidence.

Quick Answer

ISO1452DWR is an isolated, full-duplex RS-485 and RS-422 transceiver from Texas Instruments with a maximum data rate of 50 Mbps. It is relevant when an industrial design needs simultaneous transmission and reception through separate signal paths. Source it using the complete ordering code and a documented interface requirement. A quotation for a similar isolated bus part is insufficient until engineering has checked duplex arrangement and timing.

This guide focuses on procurement for fast controller-to-controller links rather than generic serial networking. At these speeds, the channel includes cable, connectors, traces and the receiver as well as the purchased IC. An installation that works at a lower clock rate may not preserve the same margin after throughput increases. The RFQ should therefore identify whether the order supports an unchanged production board, a repair or a new design still awaiting qualification.

Key Specifications

TI specifies full-duplex operation and a 16-pin wide-body DW SOIC package for this orderable device. The family provides galvanic separation between its logic and bus domains. There is no integrated isolated power supply, so the sourcing package should also identify the approved power components on both sides of the barrier.

Treat layout dimensions and insulation conditions as controlled parameters. The body width alone does not describe the installed barrier: copper routing, board slots, contamination and enclosure design also matter to system qualification. Keep a copy of the relevant data sheet revision with the approved BOM so later maintenance teams can understand which requirements informed the original choice.

  • Confirm the 50-Mbps maximum against required throughput, line coding and timing margin rather than equating it with application payload speed.
  • Check the specified logic-side supply of 1.71 V to 5.5 V and bus-side supply of 3 V to 5.5 V.
  • Review separate transmit and receive pin functions against the schematic and connector pinout before approving a quotation change.

Where to Use This Part

Potential evaluation settings include motion-control interconnects, industrial gateway links and separate command and feedback paths. Full-duplex operation can suit systems that need return information while a controller is sending commands, provided the complete network architecture uses the appropriate signal pairs.

A useful acceptance exercise transmits a repeatable pattern while checking received errors across expected supply and temperature conditions. Add installation changes such as connector adapters only when they are included in the approved design. The goal is to test the proposed system, not to assume that the maximum number printed on a transceiver page establishes the performance of every assembled link. A production sourcing decision should cite that system evidence.

  • For a motion-control link, allocate a timing budget across the transmitter, cable, receiver and processing logic.
  • For an industrial gateway, define which pair carries each direction and verify that field wiring instructions match the connector.
  • For a modular machine, test different module combinations and cable lengths instead of qualifying a single favourable assembly.

Pricing and Lead Time

Request pricing for ISO1452DWR with the intended build quantity and release schedule. Specify whether the assembly process needs continuous tape, and ask the supplier to identify any split lots. Include the geographical delivery point and the documents that receiving inspection expects. An otherwise attractive commercial response may be unusable if it omits the ordering suffix or proposes a package that the board cannot accept.

No live availability or fixed price is established here. Obtain a dated quotation and distinguish quantities offered from quantities that still require sourcing. A delivery proposal should identify its assumptions, including document release and transport arrangements, so the buyer can compare it with the actual assembly deadline.

For repeated builds, organise requests around confirmed demand rather than adding a speculative buffer without an owner. Record who may revise the quantity and who may approve a technical deviation. Fast industrial interfaces are often qualified as part of a larger board; the administrative cost of reopening that qualification can exceed a small apparent unit-price saving.

Common Alternatives

Alternative selection begins with full-duplex topology. A half-duplex device changes the way traffic shares the physical medium and may require a different connector, cable or protocol schedule. Keep these architectural differences visible before discussing electrical similarity.

For candidate parts with the same broad function, compare timing under the actual load, input thresholds, output behaviour during loss of power and bus-side operating conditions. Include package geometry and insulation requirements. A comparison should describe what was verified and what remains an engineering question, with no blanket compatibility statement based on marketing descriptions.

If the existing board cannot be changed, the approved list should name exact orderable variants and the evidence permitting each one. If a redesign is allowed, evaluate whether the system still needs the current data rate and full-duplex link, or whether another interface architecture better fits the next generation. Those design choices should be made intentionally. Procurement can support the decision with documented offers and sample quantities, but should not silently resolve an architectural question through an ambiguous purchase description.

FAQ

What distinguishes ISO1452DWR from a half-duplex transceiver?

It provides separate transmission and reception paths for full-duplex operation. The board, cable and connector must implement the intended directions. A device using one shared pair for alternating traffic cannot be assumed to preserve this arrangement.

Does 50 Mbps specify usable application throughput?

It is the manufacturer stated maximum device data rate. Payload throughput also depends on the protocol and system timing. Qualification should use the intended cable, traffic pattern, receiver loading and processing behaviour.

How should an alternate be presented in an RFQ response?

Use a separate line identifying its exact part number, package and the differences requiring review. Keep the requested ISO1452DWR offer distinct so a purchaser can approve sourcing without accidentally approving a board or protocol change.

Request an RFQ review for ISO1452DWR

Sources