SENICO Electronics

Component sourcing and inventory guides

OPA1652AIDR: Complete Sourcing Guide & Price 2026

Assess OPA1652AIDR for audio signal paths with verified dual SOIC8 identity, FET inputs, output headroom, noise measurement conditions and RFQ requirements.

Quick Answer

OPA1652AIDR is a dual FET-input audio operational amplifier from Texas Instruments, supplied in an eight-pin SOIC package. It supports a total supply range of 4.5 to 36 V and provides rail-to-rail output operation. It is a candidate for audio conditioning stages where noise, distortion and input loading must be assessed within the complete signal path.

Buying the correct amplifier begins with the gain, source impedance and expected signal level of each channel. Those conditions determine whether a component comparison is meaningful. Preserve the complete AIDR code in the request, then evaluate a dated supplier quotation separately from the electrical suitability of the approved design.

  • Exact ordering identity: dual amplifier, D-package SOIC8, tape and reel.
  • Review input common-mode limits separately from the rail-to-rail output description.

Key Specifications

TI lists this exact option with an operating temperature range from minus 40 to plus 85 degrees Celsius. Its carrier information identifies a large tape-and-reel presentation. Confirm the footprint and orientation from the D-package drawing, and keep that mechanical identity separate from other packages in the family.

An audio amplifier's headline figures are useful only with their test conditions. Specify measurement bandwidth, output level, load and gain when comparing results. Otherwise, two apparently different noise or distortion measurements may simply describe different operating points or different measurement setups.

  • Input architecture: FET inputs are relevant when source loading is important; include source resistance and its noise in the circuit assessment.
  • Speed: TI specifies 18 MHz gain bandwidth and unity-gain stability, which do not eliminate the need to check the actual feedback and load network.
  • Noise: the product data lists 4.5 nanovolts per square-root hertz at 1 kHz; a spectral-density figure is not the integrated output noise of a finished stage.

Where to Use This Part

A line-level audio stage provides a practical review case. Establish the largest expected signal, then calculate the gain and remaining output headroom at the actual supply rails. Check both channels while driving their intended loads. Clipping in a downstream stage can obscure what the amplifier itself is doing, so measure the chain at several relevant points.

For a high-impedance source, consider cable pickup and the resistance used to establish bias. Reducing amplifier input current does not remove resistor noise or interference introduced before the gain stage. Keep grounding and shielding arrangements in the evaluation record, especially if the bench setup differs from the final enclosure.

Capacitive loading deserves attention when a circuit drives cables or filters. Review the manufacturer's stability guidance and inspect the response to a small signal step. Excess ringing may not be obvious in a simple listening test. Any output resistor or compensation change should be documented with the hardware revision and checked against the required frequency response.

  • Line-level gain stages: verify maximum clean output and noise over the intended gain settings.
  • Active audio filters: measure the complete transfer function with component tolerances and the actual receiving load.
  • Sensor-to-audio interfaces: evaluate source impedance, bias network and interference before attributing all noise to the amplifier.

Pricing and Lead Time

An RFQ should identify OPA1652AIDR, the number of devices and the intended build schedule. State carrier requirements and any restrictions on mixed lots. Include an approved component-list reference so a quotation can be reconciled with the audio board that was actually evaluated.

Request the offered full manufacturer code, lot documentation and package presentation. A response for OPA1654 changes channel count and package context, while another OPA1652 package changes assembly requirements. Ask for such proposals on separate lines, with enough detail for engineering and manufacturing to evaluate them before purchase.

Compare price, currency and validity against the same quantity and delivery basis. For a pilot audio build, the evaluation quantity may be different from the later production requirement; keep both visible. A sample offer should not be interpreted as a commitment covering the complete manufacturing schedule.

At receiving, match the label to the approved code and retain the lot association. If the audio acceptance process uses a reference board or test fixture, record which hardware and measurement settings produced the baseline. This makes later investigation more useful than a general statement that a new batch sounds different.

Common Alternatives

A useful alternate evaluation starts with the circuit's dominant limitation. If noise is the concern, include source resistance and measurement bandwidth. If output level is limiting, compare load-dependent swing and supply conditions. If power consumption dominates, evaluate it alongside the required distortion and dynamic behavior.

For a proposed dual amplifier, compare pin mapping, input common-mode range, bias behavior, gain stability, output loading and recovery. Do not infer rail-to-rail input operation from a rail-to-rail output label. Reuse the same source, load and analysis settings so differences between candidates can be interpreted fairly.

Changing to a quad amplifier can consolidate channels but also changes the board and assembly. Review placement, routing and channel interaction in the finished product. Treat that proposal as a design revision whose benefits must include the cost of a new layout and qualification, rather than as a purchasing shortcut.

The approved decision should name the complete replacement code and the circuit revision on which it was tested. Keep any remaining concerns visible to the buyer before a production order is released.

FAQ

Is OPA1652AIDR a rail-to-rail input amplifier?

The relevant headline feature is rail-to-rail output. Check the specified input common-mode range separately at the intended supplies and signal levels.

Can one noise-density number predict audible system noise?

No. Source resistance, gain, bandwidth, power rails and layout contribute to the result. Measure the finished signal path with a defined bandwidth and input condition.

Why keep channel count explicit in a sourcing request?

OPA1652 is dual, while the related OPA1654 is quad. A channel-count change can require a different package, board routing and validation even when the family characteristics are related.

Request a quotation for OPA1652AIDR with your build requirements

Sources