SENICO Electronics

Component sourcing and inventory guides

OPA202ID: Complete Sourcing Guide & Price 2026

Evaluate OPA202ID for precision analog purchasing: SOIC ordering details, error budgets, capacitive loads, temperature conditions and a complete RFQ checklist.

Quick Answer

OPA202ID is a Texas Instruments single precision bipolar operational amplifier supplied in an eight-pin SOIC package. Select it by the complete ordering code and the actual analog error budget. Its combination of low offset, modest bandwidth and capacitive-load capability deserves evaluation in measurement circuits; a short distributor listing cannot establish whether it meets your circuit requirements.

For an existing assembly, start with the approved bill of materials, schematic revision and procurement drawing. For a new design, ask engineering to establish allowable offset, input leakage, output swing and settling behavior before purchasing evaluation quantities. The objective is a documented decision that connects the ordered device to the measurement channel, rather than a choice based only on a familiar amplifier family name.

Key Specifications

The manufacturer ordering page and electrical tables answer different questions. The ordering page identifies the saleable package; the datasheet defines test conditions. Record both documents in the purchasing review so that a temperature field or headline typical value does not silently become a guaranteed system specification.

Pay particular attention to temperature. TI lists the exact OPA202ID ordering entry with a range extending to 120 degrees Celsius, while the principal electrical specification conditions in the datasheet cover minus 40 through 105 degrees Celsius. Ask the responsible engineer to resolve the required operating condition rather than extending every electrical limit to the broader ordering range.

  • Ordering identity: OPA202ID uses TI package code D, an eight-pin SOIC, with a manufacturer tube quantity of 75. Carrier quantity does not establish a seller minimum order.
  • Electrical envelope: the documented supply range is 4.5 to 36 V; typical gain bandwidth is 1 MHz. A typical bandwidth value is not a complete settling guarantee.
  • Precision conditions: the datasheet specifies maximum offset and bias-current limits under stated supply and temperature conditions. Copy the relevant limits into the design review, including their conditions.
  • Board interface: check the D-package pin assignment, footprint and amplifier input/output headroom. This device should not be selected on an assumption that both inputs and output reach either supply rail.

Where to Use This Part

A useful evaluation starts with the signal path. Draw the sensor, cable, protection network, gain-setting resistors, filter and downstream converter as one circuit. Input bias interacting with source resistance can contribute measurement error, while the output load can change settling and stability. These effects remain relevant even when the amplifier offset looks small in isolation.

For a capacitive load, reproduce the intended cable and filter arrangement on the evaluation board. Observe the response to representative input changes and check recovery after overload. Treat a laboratory pass as evidence for the tested conditions, then extend the review across the actual supply and ambient requirements.

  • Precision industrial measurement: evaluate offset, drift and resistor tolerances together, then decide whether factory calibration or field recalibration is part of the system strategy.
  • Analog filtering or buffering: examine load capacitance, output current demand and transient response, particularly when the buffer drives wiring or a converter input network.
  • Service replacement on an approved board: compare the full code and assembly revision, and retain the original acceptance test limits instead of relying on a generic amplifier substitution.

Pricing & Lead Time

This guide does not provide a current unit quotation. An RFQ should state OPA202ID, Texas Instruments, the requested quantity, delivery destination and acceptable packaging. Separate evaluation demand from the next production build and the forecast release schedule. These quantities have different handling and scheduling implications, so one undifferentiated annual total may produce an unhelpful response.

Ask a prospective supplier to identify the offered carrier, lot information, documentation scope and any handling history relevant to your process. Require a written validity period and a clear distinction between a shipment estimate and a confirmed allocation. Compare offers on the same commercial basis, including transport, currency and acceptance requirements.

Before issuing a purchase order, reconcile the quotation with the exact suffix. If the offer changes to OPA202IDR, assess the reel format with manufacturing and update the approved purchasing line when appropriate. Do not silently accept a shortened OPA202 description as the final purchase identity.

Common Alternatives

The closest purchasing discussion may involve carrier format rather than a new amplifier. TI lists OPA202IDR in the same D-package family with a different carrier arrangement. Confirm the current ordering table and manufacturing feed requirements before accepting that change. The reel option does not itself establish an offer, price or delivery commitment.

A different amplifier requires a separate technical review. Build a comparison sheet covering supply range, input common-mode limits, offset, bias current, noise, bandwidth and capacitive-load response. Keep the original circuit acceptance criteria visible, because an apparent improvement in one parameter can introduce an unacceptable tradeoff elsewhere.

FAQ

Does the ID suffix matter when buying OPA202?

Yes. Use OPA202ID as the purchasing identity and verify the D-package drawing and tube carrier. A family name alone leaves packaging and ordering details unresolved. Include any proposed carrier change in the quotation and assembly review.

Can the ordering temperature range replace the electrical test conditions?

No. Record the ordering range and the conditions attached to each electrical specification separately. The design owner should approve operation and required accuracy at the intended temperature; a catalog field does not extend every datasheet guarantee.

What should accompany an RFQ for a precision measurement build?

Provide the complete part number, quantities by build, destination, packaging preference and required documentation. Attach the relevant procurement drawing or acceptance criteria when needed, and route engineering questions about the measurement error budget through the design review.

Send an OPA202ID RFQ with your build quantities and packaging requirements

Sources