SENICO Electronics

Component sourcing and inventory guides

OPA2197ID: Complete Sourcing Guide & Price 2026

Evaluate OPA2197ID for industrial analog signal paths, with practical checks for supply range, offset, capacitive loading, SOIC packaging and RFQ terms.

Quick Answer

OPA2197ID is the SOIC-8 ordering option of Texas Instruments' dual OPA2197 precision operational amplifier. The family combines rail-to-rail input and output operation with a broad supply range. For an industrial analog board, the useful question is whether its error, bandwidth and load-driving behavior fit the complete signal path, not simply whether the package fits an existing socket.

Use this guide to turn that application question into a controlled purchase. Start with the approved schematic, the expected input signal and the downstream load. Then connect those requirements to the precise ordering code and inspection record. A quotation should confirm current commercial terms independently of the engineering assessment; this page provides neither a fixed unit price nor a promise about material available for a particular build.

  • Exact device: dual precision amplifier in SOIC8 with tube presentation.
  • Evaluate the full analog error budget and actual output load before accepting a proposed change.

Key Specifications

TI identifies OPA2197ID as a dual amplifier in the eight-pin D-package SOIC, with tube carrier information on its ordering page. Record the full number in the bill of materials. The related VSSOP ordering options use a different package code, so a quotation containing only OPA2197 does not resolve the mechanical requirement.

  • Supply range: the family supports a total supply from 4.5 to 36 V, including split-supply operation within the documented limits. Confirm the actual rail values and sequencing in the circuit.
  • Small-signal speed: TI specifies a typical gain-bandwidth product of 10 MHz. Calculate the required closed-loop bandwidth and review the relevant curves rather than treating this figure as the bandwidth of every circuit.
  • DC accuracy: TI lists a maximum input offset of 100 microvolts under its stated conditions. Carry those conditions into the error budget and distinguish typical performance from guaranteed limits.
  • Signal limits: rail-to-rail operation does not make output swing independent of loading. Check the intended input common-mode voltage and output excursion against the datasheet conditions.

Where to Use This Part

An industrial analog input board needs an error budget that covers the complete chain. Write down the smallest signal change the application must resolve, the expected temperature range, source impedance and calibration method. Allocate acceptable error to the amplifier, resistors, reference and converter. That exercise is more useful than selecting an amplifier from a single attractive specification.

Loading deserves a separate review. TI discusses capacitive-load stability and the use of output isolation in the OPAx197 datasheet. Cable capacitance, input filters and converter sampling behavior can make the assembled circuit different from a simple bench measurement. Plan a step-response check using the real load and representative operating conditions, and retain the waveform with the hardware revision.

  • Sensor interfaces: define the sensor's signal range and source impedance, then verify that gain and offset errors stay within the allocated measurement budget.
  • Reference or control-voltage buffers: evaluate the required settling behavior when the downstream load changes; document the actual output load and wiring arrangement.
  • Analog conditioning before conversion: check filter behavior, the converter's input requirements and the required recovery time after a signal step before approving the amplifier stage.

Pricing and Lead Time

Send OPA2197ID as the complete requested manufacturer number, together with the board revision and planned quantities. Identify whether tubes meet the assembly process or whether the supplier should quote a different approved carrier code. Do not let an abbreviated description such as dual precision op amp replace the controlled purchasing identity.

For comparisons, request unit price, currency, quotation validity, packaging description and the delivery assumptions. State any restrictions on mixed lots and ask which source or traceability documents accompany the actual offer. If engineering needs an evaluation quantity before the production order, separate those two requirements so that a quote for one is not mistaken for a commitment covering both.

At receiving, compare the purchase order, packing label and device marking, and retain the lot association with the boards built from it. If a supplier proposes a package or ordering-code change, route that proposal to engineering before acceptance. These are recommended purchasing controls; they do not represent a claim that a particular lot has been tested or that a particular commercial service is already included.

Common Alternatives

A carrier change and an amplifier redesign are different decisions. TI lists OPA2197IDR as a tape-and-reel ordering option in the same SOIC package family. Confirm the complete supplied code and production presentation against the assembly requirements. A VSSOP version needs a separate footprint review even though the electrical family name remains OPA2197.

For a different precision amplifier, compare both channels' pin assignment, supply limits, input bias behavior, offset over temperature, noise, output load capability and settling performance. Keep the approved test circuit and acceptance limits with the comparison. If the alternative changes the error budget, calibration procedure or stability margin, account for that engineering work when evaluating the commercial offer.

For example, a sourcing proposal may look attractive until the replacement requires a new filter or calibration step. Record those dependencies before approving the order. A modest component saving cannot be evaluated properly when the qualification effort and production changes are missing from the comparison.

FAQ

Does rail-to-rail output guarantee the exact supply voltage at any load?

No. Review the output-swing specifications under the relevant load conditions. Set the usable signal range from the complete circuit requirements rather than the rail-to-rail label alone.

Can I approve a capacitive load from the headline specification?

Use the datasheet's stability guidance and validate the actual circuit. Gain, loading and layout matter, so retain a representative response test instead of relying only on a summary value.

What belongs in an OPA2197ID RFQ?

Provide the complete part number, quantity, carrier requirement, destination and desired documentation. Ask for a dated written quotation and require approval for any proposed ordering-code or package change.

Request an OPA2197ID quotation for your analog design

Sources