Quick Answer
OPA320AIDBVR is TI's single-channel OPA320 precision CMOS amplifier in a five-pin SOT-23 package. It operates from a 1.8 to 5.5 V total supply and combines rail-to-rail input and output with a 20 MHz bandwidth specification. It is a candidate for low-voltage signal conditioning and converter buffering when the complete circuit meets the required settling and accuracy targets.
The exact device distinction matters: OPA320 is not the shutdown-enabled OPA320S. A family datasheet can show both, so use the full AIDBVR ordering code when selecting the footprint and requesting quotations. Confirm the required analog behavior before treating a similar amplifier name as a usable sourcing alternative.
- Requested device: single amplifier, five-pin DBV package, tape-and-reel ordering option.
- Qualification focus: supply limits, source impedance, output loading and settling at the selected closed-loop gain.
Key Specifications
TI's ordering information identifies OPA320AIDBVR as SOT-23 DBV with five terminals. The datasheet distinguishes this from the six-pin single-channel version that includes shutdown. Keep both the exact pin drawing and the ordering code in the design record; package dimensions alone do not define the electrical connections.
The zero-crossover input design is relevant when a signal traverses a broad common-mode range. Evaluate performance over the signal range used by the application rather than assuming that a small measurement near mid-supply represents the entire input excursion. Record supply voltage and temperature with the result.
- Supply: the 1.8 to 5.5 V operating range makes this a low-voltage device; a higher-voltage amplifier is a separate design category.
- Accuracy: TI lists 150 microvolts maximum offset under specified conditions; compare the relevant limits with the whole measurement error budget.
- Dynamics: 20 MHz bandwidth and unity-gain stability are useful selection parameters, but do not directly state settling time with every load.
Where to Use This Part
For an ADC buffer, start with the converter's acquisition interval and input network. Define the largest voltage change between samples and the permitted residual error when conversion begins. This turns an amplifier search into a measurable requirement. The correct bench question is whether the combined amplifier, filter and ADC input settles sufficiently within the available interval.
A high-impedance sensor interface needs a different emphasis. Add the effects of board leakage, connector contamination and source resistance to the amplifier input-current consideration. A nominally small input current cannot prevent error introduced by the surrounding assembly. Document cleaning and inspection needs if the application depends on very small currents.
Test large and small signal steps at representative temperatures and output loads. Inspect recovery after the input exceeds its normal working range using conditions allowed by the datasheet. Keep the gain network and output isolation components with the approved circuit so a passive substitution does not quietly invalidate the analog result.
- Converter inputs: assess acquisition settling with the actual sampling sequence and input filter.
- High-impedance sensors: account for leakage paths and source resistance before assigning the amplifier error allowance.
- Active filters: verify passband response and stability using the intended component tolerances and downstream load.
Pricing and Lead Time
State OPA320AIDBVR in the RFQ, followed by the quantity, destination and required packaging. Include the board revision or approved component-list reference so that an offer can be matched to the correct design. The procurement team should not need to infer whether shutdown capability was intended from an abbreviated part description.
Ask suppliers to identify the manufacturer code on the offered label, the carrier presentation and the supporting lot documentation. If the quote proposes OPA320S, a dual version or a different package, request a separate line item. This gives engineering a clear comparison rather than hiding a functional change inside an otherwise ordinary price response.
For a meaningful commercial comparison, obtain price basis, currency, quote validity and the quantity covered by each proposed delivery. State whether cut tape is acceptable for evaluation and what the production line requires. These assembly conditions can matter even when electrical identity is unchanged.
At receiving, reconcile the supplied label with the approved full code and preserve the lot link to the manufactured boards. Keep any exception visible until it is resolved. Neither the manufacturer documentation nor this article establishes a current seller-specific quantity or dispatch commitment; obtain those terms in the actual written offer.
Common Alternatives
A proposed shutdown-capable version addresses a different system requirement and uses another pin arrangement. Review how the control signal is driven, what happens during startup and whether the board supports the necessary connection. Adding power control should be treated as an intentional circuit change with its own test cases.
For another single low-voltage amplifier, compare common-mode behavior, bias current over temperature, offset limits, noise, capacitive-load stability and settling. A higher headline bandwidth can introduce new layout or stability concerns and may not improve the converter result. Evaluate the candidate in the same circuit and measurement setup.
Write the acceptance decision around the application metric: conversion error, filter response or sensor accuracy. Include any changes to resistors, compensation or production inspection. This lets purchasing compare the full cost of approving an alternate instead of treating a nominally similar package as sufficient evidence.
FAQ
Does OPA320AIDBVR include a shutdown pin?
No. The ordinary OPA320 single amplifier uses five pins. The datasheet identifies OPA320S as the shutdown-enabled single version with a different pin count.
Can the 20 MHz figure prove that an ADC will settle correctly?
No. Settling depends on gain, output loading, filtering and the ADC acquisition interval. Test the complete input network using the actual sampling sequence.
What is the main risk when shortening the RFQ to OPA320?
The abbreviated name leaves package and carrier unresolved and can obscure a proposal for another family member. Retain the full ordering code and require explicit approval for changes.
Request a quotation for OPA320AIDBVR with your build requirements
Sources
- TI OPA320AIDBVR ordering details (checked 2026-10-02)
- TI OPAx320x datasheet SBOS513F (checked 2026-10-02)