SENICO Electronics

Component sourcing and inventory guides

OPA4202ID: Complete Sourcing Guide & Price 2026

Review OPA4202ID quad amplifier specifications, SOIC14 packing, signal limits and purchasing inputs before evaluating a quotation or another package option.

Quick Answer

OPA4202ID is Texas Instruments’ four-channel precision bipolar operational amplifier in a 14-pin SOIC package. It suits designs that need several analog gain, filtering or buffering stages and can accommodate its supply and signal-range requirements. The complete code matters: channel count, package and shipping carrier should remain explicit in both the schematic review and the purchasing request.

For sourcing, treat this device as an analog design choice before treating it as a line on a quotation. Offset, source impedance, output loading and temperature conditions determine whether it meets a circuit’s error budget. The manufacturer’s ordering page identifies the part, while the datasheet supplies the conditions behind electrical limits. Neither source establishes a current SENICO selling price or delivery commitment.

Key Specifications

Separate typical performance from guaranteed limits, and keep the measurement conditions attached to each number. The reviewed datasheet’s electrical table generally starts from a 25°C ambient temperature, ±18 V supplies and a 10 kΩ load unless a row states otherwise. A specification copied without its conditions can give a misleading impression of achievable system accuracy.

  • Architecture and package: four amplifier channels in SOIC, TI package code D, with 14 pins. The exact OPA4202ID ordering entry specifies a tube carrier containing 50 devices.
  • Operating envelope: the family supports total supplies from 4.5 V to 36 V. Its input common-mode range requires headroom from both rails; do not assume it accepts signals at either supply rail.
  • Performance reference points: 1 MHz gain-bandwidth product, typical input voltage-noise density of 9 nV/√Hz at 1 kHz, and maximum input offset of ±200 µV at the stated 25°C table conditions.
  • Temperature interpretation: the ordering entry lists −40°C to +125°C, while the reviewed electrical table specifies several limits over −40°C to +105°C. Confirm the required parameter limits beyond that table range with TI before qualification.

Where to Use This Part

Begin with the signal levels at every stage, including startup and fault conditions. A circuit powered from a single supply may need a suitable reference to keep its inputs within the permitted common-mode range. Check output swing under the intended load separately; an acceptable input level does not prove that the output can deliver the requested waveform.

For high-impedance sources, include input bias current and resistor tolerances in the error budget. For low-frequency measurements, examine offset, drift and low-frequency noise together rather than choosing an amplifier from one noise figure. The data-converter reference, grounding and board leakage may also limit the result. These are engineering checks, not performance promised by purchasing the component.

Four channels in one package can simplify placement, but the board still needs supply decoupling, a reviewed return-current path and sensible treatment of unused channels. Test representative combinations of active channels and loads. A buffer connected to a long cable or capacitive input deserves a stability assessment under the actual circuit conditions.

  • Multi-channel measurement front ends: evaluate separate conditioning stages for low-frequency sensor signals, with gain and input-range checks for each channel.
  • Reference and bias distribution: assess buffering where several analog blocks need controlled reference levels, including load changes and settling requirements.
  • Active filtering and slow control signals: compare the required closed-loop bandwidth, output current and acceptable error with the documented amplifier limits.

Pricing & Lead Time

An RFQ should identify OPA4202ID, the requested quantity, receiving location and required delivery date. Specify whether tubes are required or whether a separately identified reel option can be considered. TI’s listed standard pack quantity describes manufacturer packaging; it does not establish a seller’s minimum order or the quantity obtainable through a particular quotation.

Include acceptance requirements that affect the commercial comparison, such as manufacturer labeling, lot information, package condition and documentation needed by your receiving process. Where an analog design has strict drift or noise requirements, reference the approved specification and test conditions rather than asking for an undefined higher grade. Any special inspection or documentation remains subject to explicit confirmation in the offer.

Compare quotations using the same part identity and delivery basis. Record quantity, packing, freight assumptions, offer validity and any estimated dates. If a proposed shipment uses several lots, make that visible to engineering and receiving before acceptance. This preparation helps expose differences between offers without assuming that price, allocation or dispatch timing has already been confirmed.

Common Alternatives

OPA4202IDR is the manufacturer’s SOIC14 reel ordering option. Compare it first when the electrical choice is settled but the assembly line prefers tape and reel. Confirm the carrier, exact label code and purchase-order approval; similar part text should not conceal a change in what receiving expects.

OPA4202IPWR is listed in TSSOP14. It offers another package choice within the same amplifier family, but its mechanical footprint requires a separate layout and assembly review. OPA2202ID belongs to the dual-channel member of the family, so it cannot satisfy a four-channel bill of materials through a simple one-for-one quantity substitution.

For a broader amplifier change, write down which requirement is driving it: input range, supply voltage, channel count, noise, drift or loading. Compare complete specifications at matching conditions and validate the revised circuit. A shared family name or similar headline bandwidth is insufficient evidence for approving another device.

FAQ

How many amplifiers are inside OPA4202ID?

It contains four amplifier channels. Verify the SOIC14 pin assignment in the datasheet when allocating inputs and outputs; the dual OPA2202 has a different channel count and package pin arrangement.

Does the 50-device tube listing define the order quantity?

No. It describes the manufacturer’s standard carrier quantity for this code. The offered sales quantity, packing arrangement and commercial conditions must be stated in the quotation.

Can every electrical limit be assumed valid through +125°C?

No. The ordering range and individual electrical-table conditions are distinct. The reviewed table gives several limits through +105°C. Obtain manufacturer clarification for parameters required above that range instead of extending their limits by assumption.

Send an OPA4202ID RFQ with quantity, packing and delivery requirements for quotation review.

Sources