SENICO Electronics

Component sourcing and inventory guides

STM32L071C8T6: Complete Sourcing Guide & Price 2026

Check STM32L071C8T6 memory, voltage option, LQFP48 packaging and low-power design requirements before comparing quotations or approving another ordering code.

Quick Answer

STM32L071C8T6 is an STMicroelectronics Cortex-M0+ microcontroller with 64 KB of Flash, supplied in a 48-pin LQFP package. It is a candidate for compact controllers that spend substantial time waiting between measurements or communications. Selection should begin with the exact memory and voltage option, because specifications advertised across the STM32L071 family do not describe every ordering code.

One purchasing detail deserves particular attention: the reviewed ordering scheme assigns the version without a D option a 1.8 V to 3.6 V supply range with brownout reset enabled. STM32L071C8T6 has no D in its name. Do not copy the family headline mentioning 1.65 V into this part’s approved specification. This guide covers technical and quotation preparation; price and delivery require a current written offer.

Key Specifications

The manufacturer’s product entry and ordering table together identify the following starting points. Before board release, reconcile them with the relevant datasheet revision, package drawing and pin allocation. Peripheral presence alone does not prove that every desired function can be connected simultaneously on a particular package.

  • Processor and memory: Cortex-M0+ operation up to 32 MHz, 64 KB of Flash, 20 KB of RAM and 6 KB of data EEPROM. Budget code and working memory separately.
  • Mechanical identity: STM32L071C8T6 is listed as LQFP48, with a 7 × 7 × 1.4 mm package body. Use the manufacturer drawing for lead pitch, land pattern and assembly clearances.
  • Ordering limits: temperature code 6 denotes the industrial range from −40°C to +85°C. The unsuffixed voltage option specifies 1.8 V to 3.6 V and enabled brownout reset.
  • Useful peripherals include a 12-bit ADC with hardware oversampling, comparators, an RTC and a low-power UART. Confirm the required channel routing and clock configuration against the actual design.

Where to Use This Part

A practical evaluation starts with a time diagram of the finished product. Mark sensor startup, conversion, processing, communication and sleep intervals. The MCU is only one contributor to energy use: regulators, pull resistors, sensors and an external radio can dominate the result. Measure representative cycles before estimating battery endurance; a single datasheet sleep-current figure cannot establish service life.

The 64 KB Flash budget also deserves early attention. Include the boot process, communication stack, calibration handling and error reporting when measuring the compiled image. Reserve RAM for worst-case buffers and interrupt activity. The EEPROM can support retained parameters, but software should manage write frequency and interrupted updates rather than assume storage behaves like unlimited working memory.

  • Periodic measurement nodes: assess RTC wake scheduling, ADC setup time and sensor power control for a controller that samples, records a result and returns to a lower-power state.
  • Simple field interfaces: review low-power UART timing and protocol recovery where a host exchanges short commands or status messages with the controller.
  • Configuration and logging controllers: use the documented memory organization to separate executable firmware, temporary data and retained settings, with recovery behavior tested after a supply interruption.

Pricing & Lead Time

Prepare a request using STM32L071C8T6 in full, together with quantity, delivery destination and required receipt date. Identify whether the bill of materials permits another packing suffix, and distinguish engineering evaluation quantities from a production requirement. A quotation should state the offered manufacturer code clearly enough for the buyer to compare it with the approved bill of materials.

Document handling requirements that affect acceptance: manufacturer labels, lot or date-code constraints, package condition and any required traceability paperwork. If the assembly process requires a specific carrier, state it before comparing offers. Requested documentation or inspection remains a purchasing requirement until the seller explicitly confirms what accompanies the proposed material.

Compare commercial offers on the same scope, including quantity breaks, packing, freight basis and quotation validity. Ask whether the proposed delivery is confirmed or estimated, and record any condition attached to it. Neither an online family description nor this guide establishes a transaction price, an allocated quantity or a committed shipment date.

Common Alternatives

STM32L071C8T6TR is listed by ST alongside the base code. The ordering scheme identifies TR as tape and reel, so it is a useful packing comparison when assembly equipment requires a reel. Confirm the exact offered code and packing specification rather than silently editing the purchase order.

STM32L071C8U6 appears in the same product table but uses UFQFPN48 instead of LQFP48. That mechanical change requires a board and assembly review even though the family and memory designation look familiar. STM32L071C8T7 is another listed LQFP48 ordering code; its temperature code belongs to a different specified range and still needs approval against the project requirements.

If more firmware space is needed, reopen the memory and peripheral selection deliberately. A family’s higher memory ceiling does not upgrade the purchased C8 device. Record the proposed exact code, package, software implications and qualification work before accepting a revised bill of materials.

FAQ

Does STM32L071C8T6 have 192 KB of Flash?

No. The C8 product entry specifies 64 KB. Higher Flash capacities mentioned for the broader family are different memory options, so firmware planning and purchase documents must use the exact C8 specification.

Can this exact ordering code be specified for a 1.65 V supply?

The reviewed ordering scheme gives the version without D a 1.8 V to 3.6 V range with brownout reset enabled. Do not assign the separate D option’s lower supply limit to STM32L071C8T6.

What should be checked when an offer adds TR?

ST defines TR as tape and reel. Compare the complete offered code, carrier and assembly requirements with the approved order; a packing change should be documented even when the underlying device selection remains appropriate.

Request a quotation for STM32L071C8T6 with quantity, packing and delivery requirements.

Sources