SENICO Electronics

Component sourcing and inventory guides

TPS40070PWP: Complete Sourcing Guide & Price 2026

Evaluate TPS40070PWP for industrial power modules: source-only operation, switching constraints, package checks and an evidence-based quotation checklist.

Quick Answer

TPS40070PWP is a Texas Instruments synchronous buck controller for an external power stage. TI identifies this complete orderable as ACTIVE, in a 16-pin PWP HTSSOP package with tube packing. It supports a 4.5 V to 28 V input range and source-only operation. It is a candidate for industrial power-module evaluation when the system needs a configurable controller and the engineering team can qualify the surrounding circuit.

Begin selection with a rail specification: input extremes, output tolerance, continuous load, transient demand and startup sequence. A controller designation alone cannot establish the finished converter current rating. For an existing assembly, retain its validated schematic, component revisions and test limits alongside the purchasing record. For a redesign, compare the cost of qualifying the complete power stage with the value of retaining its flexibility.

Key Specifications

The useful specification is the one that closes a design constraint. Record operating limits separately from absolute maximum ratings, and keep the conditions attached to each electrical value. Avoid turning an attractive headline into a requirement that the assembled board has never demonstrated.

TI specifies nominal pulse widths of at least 250 ns for reliable operation. As an initial engineering screen, a hypothetical 12 V to 1 V converter at 500 kHz has an ideal on-time of roughly 167 ns. That calculation flags a conflict before component selection; it is not a complete switching model. Revisit frequency or conversion architecture, then validate the actual waveform and operating corners.

  • Control architecture: voltage-mode regulation with voltage feed-forward and external high-side and synchronous N-channel MOSFETs.
  • Programming: switching frequency up to 1 MHz, soft start, undervoltage lockout and short-circuit protection are configurable.
  • Assembly identity: TPS40070PWP uses the PWP 16-pin package; TI lists an operating ambient range of minus 40 to plus 85 degrees Celsius.

Where to Use This Part

TI lists industrial equipment and power modules among the family applications. The following evaluation workflow translates those categories into practical review tasks; it does not describe a qualified customer design.

For a module feeding several downstream loads, write a test matrix before choosing the final bill of materials. Include startup into the intended load, supply ramp variation, rapid load changes, output short circuit and recovery. Capture input, output and switching waveforms together so an apparent regulation problem can be traced to the event that preceded it.

For equipment maintenance, compare a failed board with a known working revision before substituting power components. A controller replacement can leave an underlying damaged MOSFET, degraded capacitor or incorrect feedback component unresolved. Establish acceptance criteria for the repaired assembly, including behavior after warmup. Keep measurements linked to the board serial number and component lot used.

Lay out the review around current paths and measurement access. Decide where the team will probe the switching node, output ripple and load current without changing the behavior being measured. Record probe setup with the results. This makes later engineering changes easier to compare than isolated oscilloscope screenshots.

Keep the qualification evidence useful to both engineering and purchasing. Identify which component changes require another thermal run or transient test, and state who can approve an exception. A clear release record prevents a later sourcing decision from silently changing the conditions under which the power module was accepted.

  • Industrial power modules: evaluate the complete converter across the documented input and load envelope.
  • Existing control equipment: use the original rail requirements and approved board revision as the starting point for service purchasing.

Pricing and Lead Time

Request a quotation using the full TPS40070PWP code, required quantity, assembly schedule and approved packaging. Ask the supplier to distinguish an offered quantity from a planned replenishment quantity, and request written confirmation of delivery assumptions. This article provides no current commercial price, stock quantity or dispatch commitment.

Include any lot restrictions, traceability documents and incoming inspection requirements in the request. Resolve these points before comparing offers: a quotation for another carrier format may require additional assembly planning, while a proposal that omits documentation can create work at receiving. Record who approved each deviation and which purchase order it affects.

For continuing production, connect purchasing decisions to the power-stage change process. If a supplier proposes an alternate device, route it to engineering with the exact manufacturer code and supporting documents. A procurement shortage does not remove the need to recheck the circuit. Use the RFQ response as commercial evidence and the design record as technical evidence.

Common Alternatives

TPS40071PWP is a related controller identified in the same TI datasheet, but it permits source and sink operation. That difference matters when another circuit can energize the output. Do not approve it solely because the family name and package resemble TPS40070PWP.

A different buck architecture is another design path. Prepare a comparison matrix covering input range, output requirements, control method, power-stage components, footprint and verification effort. Ask which existing tests remain applicable and which must be repeated. The decision should include firmware or sequencing dependencies where they exist, rather than stopping at a short component feature list.

FAQ

Does TPS40070PWP include the power MOSFETs?

No. It drives external MOSFETs. Review the complete power stage when determining current capability, thermal performance and suitability for the intended industrial rail.

What does source-only operation change?

TI describes TPS40070 as preventing negative inductor current from building up. Consider that behavior during startup and whenever another source can drive the output, then verify the actual system sequence.

What should accompany an RFQ for an existing design?

Provide TPS40070PWP, quantity, package requirements and the approved assembly revision. State documentation and inspection needs explicitly, and ask for written price and delivery confirmation before making a purchasing commitment.

Request a TPS40070PWP quotation for your approved design

Sources