Quick Answer
TPS54331DR is Texas Instruments' eight-pin SOIC ordering option for a non-synchronous step-down converter with a 3.5 to 28 V input range and a 3 A output-current rating. It integrates the high-side switching MOSFET and uses an external power stage around it. Selecting the correct device therefore begins with the complete regulator circuit, not the current figure alone.
For an existing board, ask engineering to identify the approved diode, inductor, capacitors and compensation network together with the DR code. For a new design, establish input extremes and the required output before comparing quotations. The commercial discussion should use those settled requirements and a dated offer rather than an assumed market price.
- DR identifies the SOIC D package with tape-and-reel presentation.
- The 3 A rating is a device capability that still requires a thermal and power-stage assessment in the intended board.
Key Specifications
TI distinguishes the D-package SOIC from the thermally enhanced package offered elsewhere in the family. Keep the exact package drawing in the component record. Similar top views can conceal an important difference in how heat reaches the circuit board, so a general SOIC8 description is insufficient for a package change.
The regulator's operating conditions should be written as a matrix: minimum input, maximum input, output voltage, steady load, peak load and ambient temperature. Add startup and fault conditions. This makes the design review reproducible and gives procurement a clear reason for preserving the surrounding approved components.
- Control: the nominal switching frequency is 570 kHz; use the datasheet design procedure when selecting the output filter and compensation.
- Light load: Eco-mode skips pulses to reduce consumption, so inspect the actual rail waveform when the downstream electronics are idle.
- Startup: adjustable slow-start and programmable undervoltage lockout support system sequencing, subject to the selected external components.
Where to Use This Part
A small industrial controller powered from an intermediate DC bus is a useful evaluation scenario. Measure the bus during connection, disconnection and nearby load switching. The normal label on a power supply does not describe every transient at the regulator pins. Protection and filtering should be chosen from the measured or specified system environment.
The external rectifier is part of the electrical and thermal assessment. Review its voltage, current and dissipation requirements with the rest of the power stage. A procurement substitution for that diode can change the board's operating temperature even though the converter number remains unchanged. Apply the same release discipline to the inductor and capacitors.
Validate load steps using the production layout and a realistic cable or load connection. Record output ripple with an appropriate measurement arrangement, and distinguish measurement artifacts from actual rail behavior. Keep the waveforms, ambient conditions and component revisions together so that a later sourcing proposal can be judged against a known baseline.
- Embedded control rails: test startup with the actual downstream capacitance and reset thresholds.
- Distributed electronics: assess input wiring disturbances and the thermal behavior inside the final enclosure.
- Battery-fed equipment: examine the low-load waveform and shutdown behavior against the product operating cycle.
Pricing and Lead Time
An RFQ for TPS54331DR should specify the requested full code, build quantities and carrier requirement. TI identifies this option as SOIC8 on a large tape-and-reel carrier. If a supplier offers the tube code TPS54331D, have manufacturing review how that presentation will be handled before purchasing accepts it.
Request a written quotation showing currency, quantity basis, validity and the proposed schedule for each delivery. Identify the documents needed for receiving, including the manufacturer's ordering identity and lot information associated with the offered material. Ask the supplier to describe any packaging change rather than leaving receiving staff to infer it.
Separate evaluation quantities from production allocation. An engineer may need enough devices to qualify a revised power stage while the released design continues to use the original assembly. Label the purpose of each order so that experimental material cannot be mistaken for the approved production line item.
At receipt, reconcile package and carrier labels with the purchase order. Preserve the lot association through assembly and link any observed power-stage issue to the actual board revision. This article supplies purchasing questions, not a statement that a particular seller holds a tested lot or can meet a fixed delivery date.
Common Alternatives
Begin an alternate review by deciding whether the proposal changes packaging or converter behavior. A tube presentation of the same package needs manufacturing acceptance. A different thermal package needs layout and assembly review. A different regulator requires a new check of topology, control loop, protection and external components.
A synchronous buck converter can be a redesign candidate when efficiency or board area motivates a change, but removing the external rectifier alters the power-stage architecture. Do not evaluate that proposal only from pin count or output current. Document the revised schematic, thermal model and acceptance tests.
Compare the total change cost, including any new inductor, capacitor qualification, electromagnetic testing and production fixtures. The approved alternative should have a complete manufacturer number and a released board record. Until then, treat the proposal as engineering evaluation material with unresolved dependencies, even if its commercial terms appear attractive.
FAQ
Is TPS54331DR a synchronous buck converter?
No. TI describes TPS54331 as non-synchronous. Review the external rectifier and complete power stage when evaluating the device or a proposed alternative.
Does the 3 A rating guarantee continuous operation in every enclosure?
No. Board copper, input and output conditions, external component losses and ambient temperature determine the thermal result. Validate the released assembly at its intended operating extremes.
Is TPS54331D the same purchasing presentation as TPS54331DR?
TI lists the D code in tubes and DR on tape and reel. Confirm the accepted carrier and manufacturing handling requirements before changing the purchasing line.
Request a quotation for TPS54331DR with your build requirements
Sources
- TI TPS54331DR ordering details (checked 2026-10-02)
- TI TPS54331 datasheet SLVS839H (checked 2026-10-02)