Quick Answer
TPS62135RGXR is a Texas Instruments synchronous step-down converter offered in an 11-pin RGX VQFN-HR package. The device family supports a 3 to 17 V input range and a rated output current of 4 A. Its sourcing review should connect the exact ordering code to the approved power-stage design, including the selected inductor, capacitors and startup behavior.
For a buyer, the important distinction is between obtaining the intended device and validating the complete supply. A converter's current rating does not prove that an arbitrary board can deliver that current continuously. Ask engineering for the qualified bill of materials and operating envelope before accepting a substitution. The price discussion below is a quotation checklist; it does not promise a current quantity, dispatch date or fixed commercial price.
- Exact converter: 3 to 17 V input, 4 A family rating, eleven-pin RGX package.
- Review thermal conditions, passives and shutdown behavior alongside the semiconductor identity.
Key Specifications
TI's ordering record specifies a 3 by 2 mm package with 11 pins and lists the RGXR carrier as a large tape-and-reel option. Preserve the complete suffix in assembly documentation. Do not select a footprint from a generic QFN label: use the manufacturer's RGX drawing and the board's approved land pattern.
- Conversion range: the family specifies inputs from 3 to 17 V and adjustable outputs from 0.8 to 12 V. Check the actual input extremes and required operating point against the datasheet.
- Control choices: the MODE input selects automatic power-saving operation or forced PWM. Make the intended light-load behavior part of the schematic review rather than leaving a control pin assumption undocumented.
- System signals: enable, power-good and soft-start/tracking functions support power sequencing. Verify their connections against the board's power-up and power-down requirements.
- Variant distinction: TPS62135 provides output discharge during shutdown; TI identifies different discharge behavior for TPS621351. That extra digit is electrically meaningful.
Where to Use This Part
TI identifies intermediate-rail and point-of-load supplies among the family applications. For a proposed design, turn that broad description into a measurable acceptance plan: minimum and maximum input, output tolerance, load steps, allowed ripple, ambient temperature and the board area available for heat spreading. Treat these as design inputs, not as results already demonstrated by your hardware.
The procurement package should include the approved versions of nearby passives. When purchasing substitutes for an inductor or capacitor, route those changes through the same engineering review as a converter change. Keep prototype results associated with the actual assembly revision. A test report for another copper layout or a different passive set may not answer the question the production buyer is trying to resolve.
- Embedded processor rails: define the downstream device's startup sequence, reset behavior and transient loading before deciding whether this converter meets the system requirements.
- Equipment with standby operation: evaluate the selected MODE setting at both light and normal load, including any system sensitivity to changing switching behavior.
- Battery-fed electronics: provide the battery's intended operating voltage range and the application's shutdown requirement; do not qualify the supply using nominal battery voltage alone.
Pricing and Lead Time
An effective RFQ separates the orderable semiconductor from the assembly service assumptions. Specify TPS62135RGXR, the quantity needed for each build, the required delivery destination and whether the production line needs an intact reel. TI lists a different RGXT carrier option, so a smaller pack should be identified explicitly rather than silently substituted on the commercial paperwork.
Ask the supplier to state the offered manufacturer code, packaging condition, date-code policy and supporting traceability evidence. Request unit price and currency together with any pack or handling charges. If the proposed quantity spans multiple lots, have the lot split recorded before the order is released. This makes it possible to compare two quotations on the same basis without assuming that a matching family name describes an identical offer.
Clarify which dates refer to supplier readiness, dispatch and delivery to your facility. Keep quotation validity and any reservation conditions in the written response. For incoming inspection, reconcile the label, quantity and packaging with the purchase order, then retain the lot reference through assembly. None of these suggested checks establishes that a particular seller already holds qualified material.
Common Alternatives
Treat carrier changes separately from electrical changes. TPS62135RGXT appears in TI's ordering information as another carrier option for this device. Confirm the supplied quantity, reel presentation and production feeder needs before approving that ordering change. Keep the original requested code and the accepted alternative visible in the purchasing record so receiving staff do not need to infer the agreement.
TPS621351 belongs to the related converter family, but its shutdown discharge behavior differs. Before considering it, ask whether the load must discharge when disabled, whether another rail can back-feed the output and how the system detects a valid power-down. Review those scenarios with engineering and record the approval. A broader converter change also needs the pin map, control behavior, passives and layout rechecked; package resemblance is not a substitute for a power-stage review.
FAQ
Does the 4 A rating remove the need for a board thermal test?
No. Qualify the assembled supply at its actual input, output, load and environment. The device rating alone does not describe your layout, enclosure or surrounding component choices.
Why must I distinguish TPS62135 from TPS621351?
TI documents different output-discharge behavior. Confirm the required shutdown sequence and downstream rail behavior before engineering approves a change between these variants.
What information makes an RFQ easier to compare?
Give the full ordering code, build quantities, carrier preference, destination and required lot documentation. Ask each supplier to state the same commercial assumptions and the dates associated with its offer.
Request a TPS62135RGXR quotation for your planned build
Sources
- TI TPS62135RGXR ordering details (checked 2026-10-02)
- TI TPS62135 family datasheet, SLVSBH3B (checked 2026-10-02)